omega.com e-mail: [email protected] latest product manuals:omegamanual.infoFOBFiber Optic Thermometer SystemsShop online atUser’s GuideMADE IN CANADA
10 4 USING THE TEMPERATURE PROBES 4.1 Caution Each time you connect a temperature probe to the unit, the probe optical connector should be cleane
11 4.3 Warning The FOBS-XX probe is quite fragile and it must be handled carefully. Please note that any probe damages are not covered by the stand
12 5 SERIAL COMMUNICATION DESCRIPTION You can communicate with your thermometer via the standard RS-232 link. A description of the c
13 FOB101 FOB102 or 104 Description b b Return enclosure temperature N/A e[1;2; ... ;n] Enable channels to scan (if no argument, scan all) f[j]
14 “f[j]” or “f[i j]” This command forces an actual temperature reading (j) for channel # i; any resulting offset will be applied to all futur
15 b) i=1. In case of a probe problem, the analog output for this channel will be forced to its maximum possible value (e.g., 10V or 20mA). c
16 ex: “y E”, with the FOB104 thermometer, will return: CH1: power:2.61, lamp attenuation: 250, CCD time: 50ms (fixed)<CR> CH2: power
17 6 ERROR CODES The following error messages are displayed under certain error conditions: RS-232 Display Analog Out Description Err2 Err2 In
18 7 FOB100-SOFT SOFTWARE PACKAGE The FOB100-SOFT software package option allows using your thermometer system in a highly flexible ma
19 You should normally see a window similar to this: In this example, we see that FOB100-SOFT has detected 2 thermometers: a FOB104
Servicing North America:U.S.A.: Omega Engineering, Inc., One Omega Drive, P.O. Box 4047ISO 9001 Certified Stamford, CT 06907-0047 USAToll Free: 1-800-
20 For each instrument, this configuration window gives some information about this particular information and allows you to set some parameters.
Warning: Doing a temperature offset adjustment on a channel will alter its reading. In effect, it alters the thermometer own calibration.
22 • To start acquiring data, click the “START” button. Conversely, to stop the acquisition, click the “STOP” button. When subsequen
23 When logging temperatures for a very long time, one needs to note that a standard Excel sheet is limited to 65535 lines. If this limit is reach
24 Adjust the “Refresh Rate” (minimum is 0.2 sec) and Min / Max to suit your viewing needs. Note that the setting of curve colors and other
25 All dials share the same Min / Max reading setting. Refresh rate is always 1.0 sec. The size of this window will adapt to the number of displaye
26 Before sending commands and receiving information from a specific module, it is necessary to select the instrument you want to interro
27 7.5.1.3 Advance serial port setting This command allows the user to force the exclusion of one or more COM ports from being scanned when clickin
28 Blank.
MADE INCANADAWARRANTY/DISCLAIMEROMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for aperiod of 13 months
3 TABLE OF CONTENTS 1 INTRODUCTION ...
M4743/0906Where Do I Find Everything I Need for Process Measurement and Control? OMEGA…Of Course!Shop online at omega.comSMTEMPERATURE䡺⻬Thermocouple,
4 1 INTRODUCTION Congratulations on the purchase of your FOB100 Series thermometer product! Your new temperature sensing system will
The following figure gives a description of the various probe configurations that are oOmega. General Purpose Probe FOBSCoupling, included with exte
6 2 UNPACKING Before using your FOB100 thermometer, check the box content to be sure all items have been included. Your package should normally con
7 3 FOB100 SERIES THERMOMETER HARDWARE REFERENCE The following figure shows the thermometer front panel: The FOB100 back panel is as follo
2) Serial communication status light: RS-232 interface. This is useful to confirm a good communication link with your PC when the FOB100software pack
9 Warning: The fiber type that is used with your thermometer is of a special type, and it is recommended that you get ALL of your p
Kommentare zu diesen Handbüchern